SUPPORT VIDEOS & TUTORIALS

PROGRAMMING A GARAGE OPENER

Wireless Keypad Model OKP-BX with Odyssey® & Destiny® Garage Door Openers

To program a CodeDodger 2 Wireless Keypad first set the PIN. To begin press and hold the program button and the up/down arrow buttons until the lights go out. Then press 3, 5, 7 program. Enter the PIN and press the program button and wait for the lights to turn off.

The pin is now set. Next on the power head press and hold program set to enter the programming menu. Then press the program set button again. To enter the remote program menu. On the wireless keypad enter your PIN number and press the up/down arrow button once. Then press the up/down arrow button again. Then press again operate the unit, the wireless keypad is now program.

Odyssey® & Destiny® Openers to CodeDodger® 2 Remote

To program the included CodeDodger® 2 remote, first press and hold the program set button. Then press the program set button again to select the remote program menu. Press and release your desired remote button. Press and release the remote button again. And finally press and release the remote button the final time to operate the door. The remote is now program.

Homelink® to Overhead Door Odyssey® and Destiny® Openers

In this video we will show you how to program the new Overhead Door Odyssey and Destiny Openers to home link. Please be sure that your Odyssey or Destiny opener is installed, limits are set, force profile has been set and you have programmed one button on the new remote to the powerhead.

Please refer to the owner’s manual for your vehicle for the specific instruction on programming home link to the garage door opener. You can also visit the home link website www.homelink.com and download the specific instructions for your vehicle. Please read through all the instructions, the necessary cautions and all the steps involved. Since the instructions will vary by vehicle manufacturer please take the time to review carefully as the instruction steps may vary from this video.

Now we first need to program one of the buttons on the remote into code archer one mode. Press and hold one of the unused buttons for 10 seconds. You will see the LED change from green to green and red. Once you see green and red release the button and now press the same button two times to confirm the change to CodeDodger® 1 you should now see the LED being read when activated. Now refer to your homely constructions, for first time training press and hold the two outer home link buttons releasing only when the Home Link indicator light begins to flash usually within 20 seconds. This clears the Home Link memory and is now ready for programming. You do not perform this step on training the additional home link buttons to other garage door openers or other home link devices.

Now we’re ready for step two. Press the appropriate home link button 1, 2 or 3 which you want to train and keep holding it until the indicator light starts flashing slowly. Once the indicator light starts flashing slowly release the button Home Link is now in training mode. You’ll now have five minutes to train your remote to the Home Link transmitter in the bumper.

Proceed to Step 3. for most vehicles you’ll be programming the remote a Home Link inside the vehicle. Please refer to the instructions in the owner’s manual or downloaded from www.homelink.com. For this vehicle the instructions locate the transmitter unit to be train near the right headlight. Stand in front of your vehicle with the original remote for the garage door opener that you wish to train.

Now we proceed to Step 4. Hold the original remote between 3 to 5 inches from the location at the transmitter. In this case the right headlight. Now press and hold the button on your original remote that is programmed to CodeDodger® 1 while keeping your hazard warning lights in view. For this vehicle the hazard warning lights will blink 3 times indicate that the training has been successful. If the training time exceeds 5 minutes the cars hazard warning lights will blink once in you’ll need to repeat steps 2 through 5.

Now we proceed to Step 6. Returned to the car and press and hold the train Home Link button and observe the indicator light. The indicator light will blink rapidly for 2 seconds and then turned to a solid continuous light.

Now we proceed to Step 7. Move to the garage door opener powerhead and find the programming buttons proceed to Step 8. Start by entering the main menu press and hold the square button until you see the long and short blue LED. Release and you will see the short blue LED only. To enter the programming menu press and release the square button you should see the short blue LED turn to a long purple LED. Pick-up the remote for your Odyssey or Destiny unit and press the button that you’ve already program to the powerhead. You should see the LED lights on the power had turned to a flashing long and short purple.

Now we proceed to Step 9. Returned to the vehicle and firmly press and hold the train Home Link button for 2 seconds and release. Repeat the press hold really sequence for 2 seconds again. The third press hold really sequence will activate the garage door opener. Congratulations you’ve completed the programming of Home Link to your new Overhead Door Odyssey and Destiny garage door opener.

Lubricating Your Garage Door Using Spray Lube

Play Video

In this video the Overhead Door of Sacramento’s team will show you where and how to lubricate your garage door with a can of spray lube. If you still have questions about lubricating your garage door after watching the video, call us and we would be happy to answer your questions!

Overhead Door Company of Sacramento™, Inc.

6756 Franklin Boulevard Sacramento, CA 95823

Insured and Bonded
State License # 355325

Order Parts Online Get what you need delivered to your door.

Call Now Button